The T Shirt is 100% cotton pre shrunk Gildan 5000 shirt. 1 Middle Weight Contender; Comfy Men’s Short Sleeve Blank Tee Shirt. 100% Cotton. Strong double needle stitched neckline and bottom hem. Shoulder-to-shoulder taping. Quarter turned. Seamless collar The Digital Printed Transfer and will be placed centered on the t shirt If there are any questions are you need any help with the design please feel free to contact us we will try our best to answer message very quickly and we would love to hear from you. If you would like bulk pricing on any of our products please let us know and we can give you special bulk pricing.
Click here to buy this shirt: Buy this February 4 1948 Alice Cooper 75 Years Thank You For The Memories Signature Ornament
Heat-setting tends to produce smooth fabric laying down the individual surface fibres to the fabric body and polyester fibres are rendered slightly stiffer so that even at a later stage tend to entangle less. Heat setting of synthetic fabrics eliminates the internal tensions within the fibre generated during manufacture and the new state can be fixed by rapid cooling. This heat setting fixes the fabrics in the relaxed state and thus avoids subsequent shrinkage or creasing of fabric. The application of heat in heat setting can be done by hot air, on a pin stenter at 220°C for 20 – 30 seconds for polyester goods and at a lower temperature range of 190 – 225°C for 15 – 20 seconds for polyamides. Acrylics may be heat set partially at 170 – 190°C for 15 – 60 seconds to reduce formation of running creases, but higher temperature should be avoided to prevent yellowing. Hydro setting is so rarely used particularly to get fuller and softer handle on polyamides at 125 – 135°C in autoclaves for 20 – 30 minutes. It can be combined with dyeing or optical brightening.
Steam setting can be done by saturated or super heated steam. During steaming, uniform treatment can be ensured by initial sequence of alternate short steaming and vacuum application for 20 – 30 min at 130°C under pressure. Super heated steam can be used in stenters and setting time is 25% shorter than for hot air on account of quicker heating up rate. Acrylic fibres have to be protested as some may undergo excessive shrinkage or loss of handle. Before the material is heat set, it should be thoroughly washed to remove spin preparations, lubricants, sizing agents and impurities as these are likely to be burned in drying heat setting making their removal difficult. Steaming at temperatures above 100°C (generally 120°C or 130°C) also reduces the pilling tendency as a result of increasing the coefficient of friction.
The different chemical finishing approaches have been made to prevent pill from accumulating on fabric surface which include the following: b) Application of enzymes (bio-finish) to 100% cotton textiles to cause removal of loose fibres in the yarn to reduce pilling tendency. The polymeric formulations bring about the binding of the loose fibres into the fabric. The products normally used in this type of finish are friction-reducing lubricants to minimize damage due to abrasion. The acrylic co-polymers, which can be modified to suit the requirements are normally used. Examples of few are: b) Application of enzymes (bio finish) to 100% cotton textiles to cause removal of loose fibres in the yarn to reduce pilling tendency In the second approach, biopolishing with cellulase enzyme is carried on 100% cellulosic or cellulose rich blend fabrics to eliminate loose fibres, which results in clean and smooth surface with improved pill rating. The bio-polishing process targets the removal of the small fibre ends protruding from the yarn surface and thereby reduces the hairiness or fuzz of the fabrics. The hydrolysis action of the enzyme weakens the protruding fibres to the extent that a small physical abrasion force is sufficient to break and remove them. Biopolishing can be accomplished at any time during wet processing but is most convenient performed after bleaching. It can be done in both continuous or batch processes. However, continuous processes require some incubation time for enzymatic degradation to take place. Removing the fuzz makes the colour brighter, the fabric texture more obvious, and reduces pilling.
Suitable for Women/Men/Girl/Boy, Fashion 3D digital print drawstring hoodies, long sleeve with big pocket front. It’s a good gift for birthday/Christmas and so on, The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness, The print on the item might be slightly different from pictures for different batch productions, There may be 1-2 cm deviation in different sizes, locations, and stretch of fabrics. Size chart is for reference only, there may be a little difference with what you get.
- Material Type: 35% Cotton – 65% Polyester
- Soft material feels great on your skin and very light
- Features pronounced sleeve cuffs, prominent waistband hem and kangaroo pocket fringes
- Taped neck and shoulders for comfort and style
- Print: Dye-sublimation printing, colors won’t fade or peel
- Wash Care: Recommendation Wash it by hand in below 30-degree water, hang to dry in shade, prohibit bleaching, Low Iron if Necessary
Home: Click here to visit Trendmugus
This product belong to huynang